Pre-Roll Automation Within Reach: How RollCraft Fills and Closes for Under $30K
RollCraft now runs in 8 states and 2 countries, bringing a complete fill-and-close line with automated Dutch Crown to producers for under $30,000.
Pre-rolls are now the top-selling cannabis category by units sold, overtaking flower (Custom Cones USA, State of the Pre-Roll Market 2026). The category generated $3.6 billion in revenue on more than 383 million units in 2025, with unit sales up 18.6 percent year over year. Demand has never been higher. Capital, for most producers, has never been tighter.
Federal tax relief from Section 280E reached only state-licensed medical and FDA-approved cannabis in April 2026. Adult-use operators, the larger share of the market, remain on Schedule I and still carry the full 280E burden. A broader rescheduling hearing is not set to begin until June 29, 2026, and the outcome is uncertain. Producers are making capital decisions before the tax picture clears.
Watch a complete sub-$30,000 fill-and-close line run start to finish (60 sec).
Why Six-Figure Systems Do Not Fit Craft Producers
Commercial pre-roll automation has long been price-prohibitive for craft and smaller producers. All-in-one commercial systems typically run well into six figures — often $120,000 and up — and assume dedicated floor space, trained maintenance staff, stable high-volume demand, and the capital reserves to absorb a large upfront commitment.
For a craft producer in a newer or volatile market, that is a difficult bet. Demand can jump, stall, then jump again, and the equipment still has to pencil out on the slow weeks.
A Complete Fill-and-Close Line for Under $30,000
RollCraft was built to close that gap. The MRB and ATC bundle at $29,995 is one of the most affordable automated fill-and-close lines that finishes every pre-roll with a professional Dutch Crown, the dense, retail-ready fold premium brands rely on. Most lower-priced options automate only filling or only closing. RollCraft automates both.
With just one or two operators, a craft producer can turn out 1,000 to 10,000 finished pre-rolls per day, closed and ready for retail packaging. Many operators report recovering the machine cost within roughly 3 to 6 months, depending on production volume, labor rates, and product mix.
Launched in 2026, RollCraft now operates across 8 U.S. states and 2 countries. That first-year traction is evidence that craft and mid-sized producers are choosing capital-efficient automation over six-figure systems.
“Craft producers don’t need to bet six figures to get into the fastest-growing category in cannabis. They need a line that pays for itself quickly. That is exactly what we built RollCraft to do.” Erik Blackerby, CTO, STM Canna
RollCraft Machines, Prices, and Specs
| Machine | Price | Function | Output | Origin |
|---|---|---|---|---|
| RollCraft MRB | $3,500 | Pre-roll filling, no pre-weighing | Up to 10,000/day, 1 operator | USA, Spokane WA |
| RollCraft ATC | $24,995 | Automated Dutch Crown closing | 72 joints under 60 sec, 2,100/hr | USA, Spokane WA |
| MRB + ATC Bundle | $29,995 | Complete fill-and-close line | 1,000 to 10,000 finished/day | USA, Spokane WA |
Both machines support 70mm, 84mm, 98mm, 109mm, and 109mm Plus cones for oversized and infused pre-rolls. 6-month warranty. Financing available through NEC. Prices current as of June 2026.
Output and payback figures vary with operator experience, material type, production volume, and infused versus non-infused product.
See What a RollCraft Line Would Cost You
Get a straight answer on price, payback, and fit for your daily volume. No sales process required.
GET MY FREE QUOTENo spam. No hard sell. Just a straight answer, usually within a few hours. Not ready for a quote? Talk to an expert free.
RollCraft Pre-Roll Automation: FAQ
How much does a complete RollCraft pre-roll line cost?
The complete fill-and-close line is the MRB + ATC bundle at $29,995. Bought separately, the MRB filling machine is $3,500 and the ATC automated Dutch Crown closing machine is $24,995. Financing is available through NEC.
How many pre-rolls can a RollCraft line produce per day?
With one or two operators, the complete line produces 1,000 to 10,000 finished, retail-ready pre-rolls per day. The MRB fills up to 10,000 per day and the ATC closes 72 joints in under 60 seconds (up to 2,100 per hour). Actual output varies with operator experience, material, and infused versus non-infused product.
What is a Dutch Crown, and why does it matter?
A Dutch Crown is the dense, twisted, retail-ready closure that premium pre-roll brands use to finish a joint. The RollCraft ATC automates this fold, so every pre-roll comes off the line packaged-ready without hand-finishing.
What cone sizes does RollCraft support?
Both machines support 70mm, 84mm, 98mm, 109mm, and 109mm Plus cones, including oversized formats for infused pre-rolls.
Can RollCraft machines handle infused pre-rolls?
Yes. The line supports oversized 109mm Plus cones used for infused and premium pre-rolls. Throughput on infused product will differ from standard flower pre-rolls.
How quickly can a RollCraft line pay for itself?
Many operators report recovering the machine cost within roughly 3 to 6 months through labor savings, though payback depends on production volume, labor rates, and product mix.
Where are RollCraft machines made, and what warranty do they carry?
Both the MRB and ATC are made in the USA in Spokane, WA, and carry a 6-month warranty backed by U.S.-based support.
How is RollCraft different from STM Canna?
RollCraft is the craft brand of STM Canna, built for producers running 500 to 10,000 pre-rolls per day. It applies STM Canna’s commercial engineering at price points designed for craft and mid-sized margins.
About RollCraft, Powered by STM Canna
RollCraft is a pre-roll automation brand built for craft cannabis producers and processors. It is engineered and manufactured by STM Canna, the company behind more than 1 billion pre-rolls produced and half of the top 20 U.S. pre-roll brands across 44 states and 14-plus countries. Both the MRB filling machine and the ATC closing machine are made in Spokane, WA, and backed by U.S.-based support and a 6-month warranty. Financing available through NEC. Contact rollcraft@stmcanna.com or (509) 204-3164.
By Erik Blackerby, CTO, STM Canna.
Comments are closed